How to repair broken concrete bird bath

Concrete is a mixture of clay, lime, san gravel and water. Some concrete contains small amounts of metal and is referred to as reinforced concrete. Empty the concrete birdbath of any water.

Lift off the basin carefully and dump out the water. Move the birdbath into a garage, basement, work shed or anywhere else. A concrete birdbath can add charm and entertainment to your garden or lawn, but as durable as concrete is, a birdbath bowl can break.

Even a bowl that has been broken. Over time, weather and other problems can cause cracks to from in the concrete , necessitating some repair work to make the birdbath look as good as new again. While heavy-duty cracks may require replacing the birdbath, most minor cracks are easily repaired with a few simple items.

A concrete bird bath is very often vulnerable to cracking and damage when it is left in the outdoors during cold winter months. This is particularly true if you live in an area where freezing and thawing are common. Unfortunately, bird baths with cracks that penetrate completely through the bowl will not hold water and will remain unusable until these cracks are repaired. It is in two semicircular pieces.

It was in good condition before that.

Sand the dried epoxy so that the surface of the repair is level with the concrete around it. Wipe the bowl with a soft, damp cloth to remove sanding residue, and return the bowl to the stand if necessary. Fill the birdbath with fresh water.

We have a cast concrete birdbath left for us at this place. Be sure the surface you are planning to coat is clean and free of dirt, rotted leaves and sticks (after all, you did leave the birdbath outside all winter!), and free of any loose and broken pieces of old concrete. Wash the surface and brush off all the debris with an old paintbrush or scrub brush. This should leave a slightly moist, but not wet, surface for the new wet cement coating to. Who the questions?

Other users of howtomendit. The more detail and information you provide in your question the easier it is for. Resurfacing is a process that uses a thin layer of cement to repair and restore cracked and damaged concrete.

Prep your cement bird bath correctly and perform any necessary repairs before resurfacing. The base has a section which has broken off. Lowes and Home depot oth sell an epoxy crack filler and sealer for concrete. It some in a large bottle and has a tip like a ketchup bottle so you can get into cracks and crevices.

Repairing a broken bird bath ? Do any of you know of something I could use to try to repair it? The only thing I can think of is silicone, but I have no idea if it would stick the cement together.

Is there any kind of glue that would work? The Fix : Avoid using a bird bath with a metal basin, or position a metal bath in a thickly shaded area where it will stay cooler throughout the day. The Tiny Bird Bath A small birdbath will not only dry out quickly, but it does not provide adequate room for multiple birds to drink simultaneously. Last summer, the bowl of our garden birdbath split into roughly equal-sized pieces and fell to the ground.

Either a large Robin stomped around too much or the cold refill on a hot day stressed the bowl. Leave undisturbed for hours. Here are a couple good ways to make use of broken bird baths: If you have an old bird bath and the top has been broken , save the base.

Carry the bird bath to the garage or any other place where it can be safe from damage while it is being repaired. Step - Clean the Bird Bath Before fixing the damage, make sure to clean every surface to ensure that the glue, caulk or epoxy will work effectively on the cracks. Quick patch epoxy is a two-part adhesive that when mixed forms a quick-binding material that immediately binds the stone pieces and cures in hours. Mix the epoxy and spread a layer on both pieces of the broken stone using a putty knife. Firmly place the stone pieces together and hold for at least two minutes to allow the pieces to set.

I thought a lot of enthusiastic bathing was rapidly emptying my (25yo) concrete bird bath , but it appears to be leaking. Any suggestions for materials to repair ? How do I repair my concrete bird bath base? There are epoxy resins that work well for this, or try a small repair using Quik Crete. You need a wire brush, a latex bonding product, concrete patching material, scrap boards, re-ro a drill with a masonry bit, and some concrete blocks or adhesive tape to hold the boards in place while the patch cures.

Chowhound Gardening food community. Join the discussion today. If pieces have broken off of the statue, look on the ground and locate them so you can reattach them. Dampen the cement statue with a garden hose until all surfaces are wet. Scrub the statue gently with a soft-bristled brush or a nonabrasive sponge to remove all dirt and grime that may interfere with the repair.

While using cement to repair a concrete birdbath seems logical, repairs made with cement tend to leak. Instea use epoxy, which works as well on concrete as it does on glass and ceramic. Apply the epoxy to both of the broken edges. Wire together and let it dry hours. Another adhesive, Bondo, formulated for car repairs, works, too.

Mix the two components with a trowel, a mixing paddle attached to a drill or by using gloved hands.